Nozzle Schedule

【#第一文档网# 导语】以下是®第一文档网的小编为您整理的《Nozzle Schedule》，欢迎阅读！

PV Elite 2012 Licensee: ZISHAN ENGINEERS (PVT.) LTD.

FileName : Untitled -------------------------------------- Nozzle Schedule : Step: 20 12:34p Sep 1,2014





Nozzle Schedule:

Nominal Flange Noz. Wall Re-Pad Cut Description Size Sch/Type O/Dia Thk ODia Thick Length mm Cls mm in. in. in. in.

------------------------------------------------------------------------------ Noz N1 Fr10 200.000 40 WNF 219.075 0.322 - - 0.00 Noz N1 Fr30 200.000 40 WNF 219.075 0.322 - - 0.00 Noz N1 Fr80 200.000 40 WNF 219.075 0.322 - - 0.00

General Notes for the above table:

The Cut Length is the Outside Projection + Inside Projection + Drop + In Plane Shell Thickness. This value does not include weld gaps, nor does it account for shrinkage.

In the case of Oblique Nozzles, the Outside Diameter must

be increased. The Re-Pad WIDTH around the nozzle is calculated as follows: Width of Pad = (Pad Outside Dia. (per above) - Nozzle Outside Dia.)/2

For hub nozzles, the thickness and diameter shown are those of the smaller and thinner section.

Nozzle Material and Weld Fillet Leg Size Details:

Shl Grve Noz Shl/Pad Pad OD Pad Grve Inside Nozzle Material Weld Weld Weld Weld Weld in. in. in. in. in.

------------------------------------------------------------------------------ Noz N1 SA-106 B 0.250 0.375 - - - Noz N1 SA-106 B 0.250 0.375 - - - Noz N1 SA-106 B 0.250 0.375 - - -

Note: The Outside projections below do not include the flange thickness.

Nozzle Miscellaneous Data:

Elevation/Distance Layout Projection Installed In Nozzle From Datum Angle Outside Inside Component ft. deg. in. in.

---------------------------------------------------------------------------- Noz N1 Fr10 0.00 6.00 0.00 Node: 10 Noz N1 Fr30 0.00 6.00 0.00 Node: 30

1


PV Elite 2012 Licensee: ZISHAN ENGINEERS (PVT.) LTD.

FileName : Untitled -------------------------------------- Nozzle Schedule : Step: 20 12:34p Sep 1,2014



Noz N1 Fr80 0.00 6.00 0.00 Node: 80

PV Elite is a trademark of Intergraph CADWorx & Analysis Solutions, Inc. 2012

2


PV Elite 2012 Licensee: ZISHAN ENGINEERS (PVT.) LTD.

FileName : Untitled -------------------------------------- Nozzle Summary : Step: 21 12:34p Sep 1,2014





Nozzle Calculation Summary:

Description MAWP Ext MAPNC UG45 [tr] Weld Areas or psig psig Path Stresses

--------------------------------------------------------------------------- Noz N1 Fr10 ... ...Failed 0.000 Failed NoCalc[*] Noz N1 Fr30 ... ...Failed 0.000 Failed NoCalc[*] Noz N1 Fr80 ... ...Failed 0.000 Failed NoCalc[*] ---------------------------------------------------------------------------

[*] - This was a small opening and the areas were not computed or the MAWP of this connection could not be computed because the longitudinal bending stress was greater than the hoop stress.

Note: MAWPs (Internal Case) shown above are at the High Point.

Check the Spatial Relationship between the Nozzles

From Node Nozzle Description Y Coordinate, Layout Angle, Dia. Limit 10 Noz N1 Fr10 0.000 0.000 0.000 30 Noz N1 Fr30 0.000 0.000 0.000 80 Noz N1 Fr80 0.000 0.000 0.000

The nozzle spacing is computed by the following: = Sqrt( ll2 + lc2 ) where

ll - Arc length along the inside vessel surface in the long. direction. lc - Arc length along the inside vessel surface in the circ. direction

If any interferences/violations are found, they will be noted below. No interference violations have been detected !

PV Elite is a trademark of Intergraph CADWorx & Analysis Solutions, Inc. 2012

3

本文来源：https://www.dy1993.cn/Q8Q.html